Chainline is how straight the chain runs from the front chainring to the rear sprocket. A perfect chainline puts both sprockets in the same plane, so the chain feels no sideways push. Derailer bikes cannot hold that in every gear, but you can still get the alignment right where it counts, and you must get it nearly exact on a single-speed.
Why it matters
When the chain is forced sideways, it rubs on things and shifts reluctantly. Sheldon Brown’s chainline article notes that a mismatch can make the chain rub against the side of a larger outer chainring while it sits on a smaller one, and can cause shifting problems, especially at the front derailer. It also lowers efficiency, though the same article says research found that loss to be minor.
So chainline is mostly a question of clean shifting, noise and a drivetrain that behaves, not of lost watts. This page makes no claim about how much faster a chain wears, because the sources do not quantify it.
Derailer bikes versus single-speeds
Because the chain moves across a cassette, a derailer bike has a different angle in almost every gear. Brown says chainline is imperfect in most gears on such a bike, and that the “correct” figure is partly opinion, depending on how the bike will be used. Derailer systems tolerate a fair amount of angle.
A single-speed has no such slack. The same source says that angle is acceptable on a derailer bike but should not be accepted on a single-speed, where getting the chainline right is quite important.
Reference chainline numbers
These figures come from one source and are measured from the frame centerline. Treat them as starting points, then check your own parts’ documentation.
| Drivetrain | Chainline | Measured to |
|---|---|---|
| Track, coaster brake, one-speed, most internal-gear hubs | 40.5-42 mm | Chain center |
| Road double (Shimano spec) | 43.5 mm | Midpoint between the two rings |
| Road triple (Shimano spec) | 45 mm | Middle ring |
| Mountain triple (Shimano spec) | 47.5-50 mm | Middle ring |
| Newer single-ring mountain bikes | 52 mm | Chain center; wider for chainstay clearance |
How to measure your own
Front
Chainline is measured from the centerline of the frame to the center of the chain. Hold a ruler against the seat tube and read the distance from the middle of the tube to the middle of the chainring teeth. On a triple, use the middle ring. On a double, use the point halfway between the two rings.
Rear
- Take the frame spacing, or the over-locknut width of the hub, which should be the same, and halve it.
- Measure from the inside of the fork end to the middle of the sprocket or cluster. For a cluster, that is the gap to the outer sprocket plus half the cluster width.
- Subtract that distance from the half-width. The result is the rear chainline.
With a single chainring, the rear figure should match the front, so the chain leans equally at both ends of the cassette. With more than one ring, the front can sit a few millimeters inward or outward depending on which rings you use most.
The sight-line check
With the wheel in the frame and no chain fitted, put your head just in front of the chainring and sight back along it toward the rear hub. The chainring should line up with the sprocket. A straightedge held against the chainring’s side helps. This is the quick test for a single-speed build.
Changing chainline
Small changes are usually easier at the front.
- Chainring spacers: on a single ring, spacers between the ring and the crank spider shift it sideways.
- Bottom bracket spindle: most modern bottom brackets are symmetrical, so a spindle 4 mm shorter moves the chainline 2 mm. Afterward, confirm the frame still clears the crank and chainring.
At the rear, spacers on the axle and re-spacing the hub move the chainline, which is the usual route when converting a multi-speed bike to single-speed. Moving spacers from one side to the other disturbs the alignment between a disc rotor and its caliper, so on a disc bike have a shop do this work and check the brake afterward.
Single-speed conversions
Dropping the derailers from a multi-speed bike rarely lines up by itself. On a threaded freewheel hub, the chainline will likely work only in the granny gear unless you re-space the axle and re-dish the wheel. On a cassette hub, simply removing the derailers and shortening the chain probably leaves a crooked chainline. Replacing the cassette with one sprocket and a stack of spacers lets you position it exactly opposite your chainring.
If you are unsure about wheel dishing, ask a shop. See also our guides on why single-speed bikes are making a comeback and why a bike shifts badly, and use rear derailleur service when shifting trouble is not alignment. For a snapped chain, see fixing a broken chain on the road.
When to see a professional
Stop and have a shop look if the chain repeatedly jumps off, a crank or chainring touches the frame, or a wheel needs re-dishing or rotor realignment. Do not ride with a chainring or crank touching the frame.
Sources
Last reviewed: October 2026.